| Id |
Description (What / When) |
Impacted Domain |
Impacted Sub Domain |
Fixed in |
| CUS56057 |
[AirPrime Q26Extreme] Parallel bus subscription with adl_busSubscribe() always returns ADL_RET_ERR_PARAM. |
SYS |
OTHER |
7.42 |
| CUS56225 |
When PIN code is disabled, the +WIND: 1 indication takes more than 30 seconds to appear. |
SIM |
OTHER |
7.42 |
| CUS55829 |
When data is continuously transmitted the data from the PC to the AirPrime WMP100 Embedded module then on CTS transition data loss is observed. |
OTHER |
OTHER |
7.42 |
| CUS55669 |
 Embedded module resets if an OAT application continuously sends data over a UART and the UART cable is kept unplugged for some time. The issue is reproducible only with both flow control enabled ( AT+IFC+2,2). |
DEVICE |
V24 |
7.42 |
| CUS56121 |
The UART signal state cannot be get for IOC_UART_SS UART IO command whereas it should be possible to get UART signal states. |
DEVICE |
OTHER |
7.42 |
| CUS55710 |
Reset of embedded module occurs after performing the following operation sequentially through OAT application:
- Exit spy mode
- Send 1st SMS
- Establish a GSM MO call
- Play DTMF
- Send 2nd SMS
- After some iteration abort the SMS2
- Resend it and abort it again. |
OTHER |
OTHER |
7.42 |
| CUS55444 |
Backtrace "!WRONG SIM CMD PARAMETER: 67xx" is received for SIM command parameter 3 every time an embedded module is started. The issue is reproducible in case false/wrong information is present in the SIM EF and the embedded module tries to read the information at startup. |
SIM |
OTHER |
7.42 |
| CUS55462 |
[AirPrime Q26Extreme] SIM card interoperability issue exists, if a bad TERMINAL_PROFILE response is received from the SIM (from SIM Toolkit Application). |
SIM |
OTHER |
7.42 |
| ANO56901 |
[InSim3 modules] When a new SIM card is inserted, the pin code is failed |
SIM |
PRES |
7.42 |
| ANO57098 |
[InSim3 modules] No proper wind messages, whenever SIM inserted or extracted. |
SIM |
PRES |
7.42 |
| ANO55935 |
If the delay to wait for ATR is too short then the error "SIMERR_TIMEOUT" is raised. This is because the reset of some SIM cards can be too long (superior to the delay to wait for ATR). |
SIM |
RESET |
7.42 |
| CUS56491 |
On using AT command AT+STGI=X to accept sending a USSD string, with the customer STK SIM the +CUSD indication is not displayed, during STK operation. |
SIM |
STK |
7.42 |
| CUS55533 |
When we continuously transmit the data every 300ms from the PC to the AirPrime WMP100 embedded module then after 3-5 minutes the CTS stays at low and never comes back to high and also AirPrime WMP100 embedded module stops receiving the data. |
OTHER |
OTHER |
7.42 |
| CUS55626 |
When more than one task are running in an embedded application and some data is read/written on an UART port using raw access mode, the data is sometimes not displayed on the desired UART and is instead displayed on the other UART. |
OTHER |
OTHER |
7.42 |
| CUS55759 |
While setting the RTC time (either with AT command “AT+CCLK” using adl_atCmdCreate() API or RTC service), if current time is set to a value more than the alarm time, the previous alarm is not deleted. |
OTHER |
OTHER |
7.42 |
| ANO56029 |
[AirPrime Q26Extreme] The unsolicited indication +CREG:0 is not displayed after RF is stopped via AT+CFUN=4. As a consequence of this issue, multiple SMS can be received. |
OTHER |
OTHER |
7.42 |
| CUS56088 |
The embedded module will reset, when PPP connection is established again and again using wvdial (On Linux-Debian) . |
OTHER |
OTHER |
7.42 |
| CUS56224 |
[AirPrime Q26Extreme] AT+CPIN=<Correct Password> command takes 35 to 40 sec to respond with OK.
During this period, most of AT commands answer +CME ERROR: 515. |
OTHER |
OTHER |
7.42 |
| ANO56265 |
Embedded modules using the T8 flash does not respond when some device is connected to the parallel port. |
OTHER |
OTHER |
7.42 |
| ANO56337 |
While making a gprs call using the ATD*99***1# command using TE, the CONNECT <speed> string is not displayed in TE data window. In case the hyperterminal is used, the CONNECT <speed> string is displayed while making a GPRS call. |
OTHER |
OTHER |
7.42 |
| CUS56514 |
If "+CBM :" indications not containing any CR (Carriage Return) are received and displayed, embedded module resets. Also, "+CBM" indications displayed are truncated. |
OTHER |
OTHER |
7.42 |
| CUS56538 |
Using WIPSoft, if the HTTP sessions are opened and closed consecutively for sometime the embedded module reset occurs. |
OTHER |
OTHER |
7.42 |
| CUS56539 |
With 1st MO call on hold and after the second MO call to an invalid number disconnects, it is not possible to switch back to the held (first) call for about 2 minutes as the AT+CHLD command returns "+CME ERROR: 3". Embedded module should ideally switch back to the held (first) call when the call to invalid number has been disconnected. |
OTHER |
OTHER |
7.42 |
| ANO56543 |
Embedded module resets, if function adl_portSendPriorityDataExt() is called from WIPSoft or Embedded application to send the data with priority on CMUX port. |
OTHER |
OTHER |
7.42 |
| CUS55528 |
An audio loss or strange noise occurs, when switching is done from DAI audio configuration at startup (AT+SPEAKER=9) to analog audio speaker (AT+SPEAKER=1,2,3 or 4) during a voice call. |
HWL |
AUDIO |
7.42 |
| ANO56193 |
[AirPrime Q26Extreme] When AT command AT+CHLD=0 is passed to embedded module, it is executed as command AT+CHLD=1 whereas in the ideal scenario, the command behavior should not be changed and should remain as AT+CHLD=0 only. |
GSM |
CC |
7.42 |
| CUS56275 |
[AirPrime Q26Extreme] Audio is opened too early in case of incoming call, and this can lead to white noise before ATA is issued. |
GSM |
CC |
7.42 |
| ANO57089 |
The embedded module does not go back to automatic PLMN search, after manual registration is rejected with GMM cause #17. Also, there is no prompt for manual selection of network. |
GSM |
PLMN_SEL |
7.42 |
| ANO57099 |
The A5/3 algorithm is disabled in the Q26 Extreme if firmware downloaded using WPK. It should be enabled by default. |
GSM |
RR |
7.42 |
| ANO56071 |
[AirPrime Q26Extreme]When SMS-STATUS-REPORT is set using unsolicited result code +CDSI and a SMS is sent then status report +CDSI indication is not received. |
GSM |
SMS |
7.42 |
| CUS56392 |
When AT+CGATT=1 is sent with correct operator of the SIM card (AT+COPS=0) and after that again sent with an incorrect network operator (only emergency call allowed) then no response is received from embedded module for AT+CGATT=1 command. For all AT command after that "+CME ERROR:515" is received. |
GPRS |
OTHER |
7.42 |
| CUS56403 |
Using WIPSoft, when GPRS bearer is started with wrong APN parameters, no error response is received. In ideal scenario, +CME ERROR: 812 should be received. This behavior is observed on AirPrime Q26Ex and not on AirPrime WMP100. |
GPRS |
SESSION_MGT |
7.42 |
| CUS57376 |
When management services for AirPrime update is done with a large patch (patch size higher than 64 kbits for a 32 Mbits flash memory or 256 kbits for a 64 Mbits flash memory), the A&D volume in flash is not available after the update. Commands regarding A&D volume (e.g. at+wopen=6) returns ERROR (e.g. CME ERROR: 561). |
Embedded RDMS |
RDMS |
7.42 |
| CUS55922 |
When a UART is used in MUX configuration, during a GPRS transfer, the network is often lost ("+WIND: 8" and "+CSQ: 99,99"). Embedded module never re-registers to operator until next power cycle. |
DEVICE |
CMUX |
7.42 |
| ANO56120 |
Wrong behavior when embedded module received a DISC0 |
DEVICE |
CMUX |
7.42 |
| CUS56232 |
When CMUX configuration is set and sleep mode is enabled (AT+W32k=1), sleep mode may not be effective. On DTR drop, PSC (sleep frame) is sent, but embedded module may not have entered in sleep mode. |
DEVICE |
MUX |
7.42 |
| ANO56428 |
When CMUX configuration is set, UART2 is opened, UART1 is closed, and sleep mode (AT+W32k=1) is enabled on UART2, then on disabling sleep mode (Wake Up), it is not able to open UART1 again. |
DEVICE |
MUX |
7.42 |
| ANO57121 |
Abnormal reset happens in CMUX during initialization of CMUX. |
DEVICE |
MUX |
7.42 |
| CUS56314 |
In specific cases (for instance after a reset and without sim card), when sleep mode (AT+32K=1) is requested, embedded module does not enter low power consumption mode. Though, MUX process is fine (PSC sent). |
DEVICE |
OTHER |
7.42 |
| CUS55196 |
When an embedded application uses the AT+CPOF command to put the embedded module into power off mode followed by wake up using the alarm management command +CALA repeatedly, then after few hours the embedded module wakes up from alarm mode with the InitType value other than ADL_INIT_RTC. |
DEVICE |
RTC |
7.42 |
| CUS54050 |
The embedded module crashes when the handshakes of UART2 are active (AT+IFC=2,2) and nothing is connected to UART2 (free). |
DEVICE |
V24 |
7.42 |
| CUS54170 |
RTS signal is followed even when RTS following is disabled with AT+IFC=0,2 command. Ideally RTS signal toggling should not have any effect after AT+IFC=0,2. No Data is displayed e.g. Response for AT, when the RTS signal is set to low with AT+IFC=0,2. AT Response should be displayed as with AT+IFC=0,2 RTS signal should not impact the behavior after setting RTS to Low. |
DEVICE |
V24 |
7.42 |
| CUS54702 |
When a band change is made with a hot reset (see +WMBS command description), the OK response is returned by the embedded module while the protocol stack is treating the band change. So when this OK response is returned by the embedded module, the protocol stack is not ready to treat any request.
In this case, sending +CSQ command to the embedded module just after the OK response of the band change with a hot reset does not return any response and no more AT commands can be sent to the embedded module (+CME ERROR: 515 response is always return). The embedded module should return an error to the +CSQ command while the band change is not terminated. |
AT |
OTHER |
7.42 |
| ANO55233 |
[AirPrime Q26 Extreme] AT+CSQ process can take more than 1 second to respond. Due to this when AT+CSQ is issued continuously +CME ERROR: 515 is received. |
AT |
OTHER |
7.42 |
| ANO55991 |
When FCM flow is opened and closed again and again using ADL FCM services by any embedded application, then a module reset is observed due to lack of memory. |
AT |
OTHER |
7.42 |
| ANO56171 |
CONNECT response is received in middle of data transfer when embedded module is switched back to ONLINE mode by ATO command in case embedded application is running in the background. Issue is observed when embedded module with ongoing GSM data call is switched to OFFLINE mode by issue of "+++", once the data transfer is started, and again to ONLINE mode by ATO command.
CONNECT response for ATO command should not be received in middle of data. CONNECT Response should be received before data transfer is resumed no matter whether an embedded application is running in the background or not. |
AT |
OTHER |
7.42 |
| CUS56395 |
When a band change is made with a hot reset (see +WMBS command description), the OK response is returned by the embedded module while the protocol stack is treating the band change. So when this OK response is returned by the embedded module, the protocol stack is not ready to treat any request.
In this case, sending +CSQ command to the embedded module just after the OK response of the band change with a hot reset does not return any response and no more AT commands can be sent to the embedded module (+CME ERROR: 515 response is always return). The embedded module should return an error to the +CSQ command while the band change is not terminated. |
AT |
OTHER |
7.42 |
| ANO56760 ANO56761 ANO56770 |
[AirPrime Q26 Extreme] AT+CSQ process can take more than 1 second to respond. Due to this when AT+CSQ is issued continuously +CME ERROR: 515 is received. |
AT |
OTHER |
7.42 |
| CUS54582 |
When an incoming SMS is received by the embedded module and if this SMS contains a header (User Data Header), this header is displayed in text mode (see +CMGF command) even if the corresponding characters are not ASCII one. Because the embedded module does not support any SMS header, it should not be returned in SMS read response (see +CMGR and +CMGL commands) and only the SMS text (User Data) should be returned in text mode (see +CMGF command) |
AT |
SMS |
7.42 |
| ANO51295 |
The Wireless CPU® returns CONNECT XXXX for AT+CGDATA=1,1 command and produces data flow even it is not located over network. |
AT |
OTHER |
7.4a |
| ANO52081 |
Wireless CPU® can reset if user wants to enter in DATA mode or exit from DATA mode on a closed port. |
AT |
OTHER |
7.4a |
| ANO52946 |
If there is only one PLMN entry in the sim card, the response of command AT+CPOL? results in the infinite loop which eventually deplete all the heap resources. |
AT |
OTHER |
7.4a |
| ANO53087 |
The Wireless CPU® resets when AT+CUSD command is issued large number of times to send an USSD in UCS2 format. |
AT |
OTHER |
7.4a |
| ANO53848 |
When repeatedly sending blocks of data for some time with AT+CPOF sent through an application at regular intervals the Wireless CPU hangs up and does not responds to AT commands. |
AT |
OTHER |
7.4a |
| ANO53934 |
The command AT+WASR=1,1,"GpioId" gives +CME ERROR: 3 instead of expected CME ERROR: 501 when the GPIO is not allocated.
Also it returns +CME ERROR: 501 instead of expected +CME ERROR: 3 when the GPIO doesn't lies in the possible range. |
AT |
OTHER |
7.4a |
| ANO54124 |
When the SIM is removed from the SIM rack while the Wireless CPU is listing the preferred PLMN (see +CPLS and +CPOL command), a reset happens. The Wireless CPU should not reset and a specific error should be returned to AT+CPOL? command (+CME ERROR: 556) |
AT |
OTHER |
7.4a |
| ANO54586 |
When the Wireless CPU® is registered on a network and camped to a cell supporting GSM and GPRS services, if the autoquadband mechanism is launched (using +WMBS command) and if a power off is requested (+CPOF, +CFUN, etc...), the Wireless CPU® launches a new registration sequence instead of making a power off. The Wireless CPU® should not register again to the network until the next start up (hot or cold restart using +CFUN command for example). This doesn't happen with a cell supporting the GSM service only (not linked to the device class) |
AT |
OTHER |
7.4a |
| ANO54934 |
On issue of AT+WOPEN=2 command, the first argument was erroneous in case of firmware version B74f. For the ideal scenario, the response should be the correct version of the OS that was released with the Firmware i.e. v06.31 for FW version B74f onwards till B74l. |
AT |
OTHER |
7.4a |
| CUS53004 |
Audio (Melody) is stopped when a Call Waiting indication is received for the second incoming call over an ongoing call. No melody is heard after the BEEP sound of the Call Waiting indication as the audio resource SPEAKER is now allocated to Call Waiting indication and context for audio (Melody) is lost. |
AT |
OTHER |
7.4a |
| CUS54251 |
In case the Wireless CPU® is in sleep mode the customer is not able to notice the mode as sleep mode because the CTS signal does not follow the DTR signal. CTS signal should not follow the DTR signal in case of normal mode but in case of sleep mode the CTS signal should follow DTR signal. |
AT |
OTHER |
7.4a |
| CUS54368 |
The Wireless CPU® provides an AT command in order to read the IMEI (see +WIMEI command), using it a large number of times (more than 1000 times) makes the Wireless CPU® reset. Ideally, the Wireless CPU® should not reset in this case. |
AT |
OTHER |
7.4a |
| CUS54579 |
No +WIND: 9 and +WIND: 2 indications are received in case AT+WAC command is issued after an attempt to make a voice call with the command ATDxxxxxxxxxx; +WIND:9 and +WIND: 2 indications should be displayed as the functionality of AT+WAC command is used to abort only SMS, SS and PLMN selection related commands. AT+WAC should not have any effect on ATDxxxxxxxxx; command. |
AT |
OTHER |
7.4a |
| ANO48610 |
Although, the phonebook record has not been changed, the phone book status is wrongly displayed in "+WIND 10" indication. |
AT |
PHONEBOOK |
7.4a |
| ANO51561 |
ATDxxxxpxxxxxxxxxxxxxxxxxxxx; calls the number with the DTMF Sequence and this sequence is stored in the LND phonebook wrongly reserving an EXT Record as DTMF sequence (after 'p') should not be stored in the LND phonebook. When the user again dials a similar sequence, the number is not stored in the LND as the EXT record has been reserved by the LND for the previous dialed number. |
AT |
PHONEBOOK |
7.4a |
| CUS54033 |
When the size of the phonebook object is set with 0xFFFF in the Wireless CPU, a watchdog reset is observed few seconds after the SIM PIN code entry (if the SIM PIN code check is enabled) or few seconds after the SIM insertion (if the SIM PIN code check is disable). |
AT |
PHONEBOOK |
7.4a |
| CUS53678 |
The PDU response of the SMS STATUS REPORT is incorrect as some extra bytes are received when status report is stored in FLASH. Also when the status report is stored in the Elementary file of SIM, the response is incorrect. |
AT |
SMS |
7.4a |
| CUS55211 |
If a user sends or write the SMS with DCS as default GSM and store it in ME memory where the character set selected is PCCP437, then the SMS data when read is not displayed correctly when ME memory is selected. The bytes in the user data field will be changed. This problem is not reproducible when SM memory is used. |
AT |
SMS |
7.4a |
| ANO53962 |
When SIM Tool Kit feature is activated and if an application requires the SETUP MENU using AT+STGI=0 command, the OK response to the command is returned after two +STGI response, even if more +STGI responses have to be returned by the Wireless CPU®. These indications are then returned as unsolicited responses instead of intermediate responses. All +STGI indication for SETUP MENU should be returned as intermediate responses. |
AT |
STK |
7.4a |
| CUS55764 |
Wireless CPU® resets when SET UP IDLE MODE TEXT with large text string is executed. |
AT |
STK |
7.4a |
| CUS56077 |
New option #2 to stop STK SETUP CALL is added. User can accept call and the call is started by applicative software. |
AT |
STK |
7.4a |
| CUS56159 |
If user wants to start the STK SETUP CALL by applicative software. A new option #2 is added (i.e. AT+STGR=4,2), so that user can use ATD to dial a call. |
AT |
STK |
7.4a |
| ANO55988 |
When a large file is transferred through more than 1 UART (physical/virtual) there may be a data loss and data corruption (some junk characters are displayed). The integrity of the transferred data may not be intact. |
DATA |
OTHER |
7.4a |
| ANO56043 |
The UART port becomes unresponsive when large data file is sent using +WIPDATA command using WIPSoft. |
DATA |
OTHER |
7.4a |
| CUS53916 |
Using WIPSoft, if the DTR signal is used to switch from DATA mode (ONLINE) to AT command mode (OFFLINE), in some cases, the V24 request does not go in to OFFLINE. Even after manually trying +++ command the transition does not occur. Wireless CPU® has to be restarted to get out of this state. |
DATA |
OTHER |
7.4a |
| CUS54044 |
If the GSM data call is first accepted and then released at the receiving end before CONNECT indication is received, then the call is just being held there without being connected, and at the dialer side it appears that the call is never answered. |
DATA |
OTHER |
7.4a |
| CUS53506 |
Power consumption does not reduce in off mode after the AT+CPOF command is issued from Open AT® application. |
DEVICE |
ADC/BAT |
7.4a |
| ANO55895 |
When a MUX session is wakeup from a sleep mode (w32k mode), the Wireless CPU® do not respond. |
DEVICE |
CMUX |
7.4a |
| ANO55897 |
During w32k mode, when an incoming call is made, after receiving "RING" indication, CMUX does not respond. |
DEVICE |
CMUX |
7.4a |
| ANO55910 |
When the N1 parameter value is higher than 127 in AT+CMUX command, the responses of the AT commands executed on the DLC are not displayed. |
DEVICE |
CMUX |
7.4a |
| ANO56020 |
On a port configured in CMUX mode with the sleep mode enabled, we can notice the missing of some PSC (sleep frame) frames. The PSC frames are correctly sent only for the first few period. |
DEVICE |
CMUX |
7.4a |
| CUS55923 |
During an incoming call, when the UART is activated in MUX mode, the physical RI pin is not triggered, ideally the physical RI pin should be triggered. |
DEVICE |
CMUX |
7.4a |
| ANO56109 |
When the user switches from AT mode to DATA mode using WIPSoft, sometimes CONNECT indication is received in between the data transfer. If any application specifically checks for CONNECT after switching from AT mode to DATA mode, this will result in a failure.
To correct this issue, a new OPIC_OAT interface has been opened and called by WipSoft 5.21. |
DEVICE |
FCM |
7.4a |
| CUS56064 |
When DTE doesn't send a wakeup response, DLC disconnection may lead to a reset. |
DEVICE |
MUX |
7.4a |
| ANO55849 |
When the UART speed is set to 9600 baud rate and a MUX session is launched on this UART port, the Wireless CPU® resets. |
DEVICE |
OTHER |
7.4a |
| CUS52710 |
With UART2 enabled for data transfer and data being transferred using Device services, a reset of the Wireless CPU® is observed when we issue AT command from UART1 immediately after data transfer. |
DEVICE |
OTHER |
7.4a |
| CUS54169 |
Customer would not be able to subscribe to the parallel bus service when UART 2 is in open state. |
DEVICE |
USB |
7.4a |
| CUS54640 |
When the host closes the USB link, the communication can be broken after restarting it. |
DEVICE |
USB |
7.4a |
| ANO43273 |
Wireless CPU® resets when making a data call over GSM bearer, by using WIP (WIPSoft) APIs. |
DEVICE |
V24 |
7.4a |
| ANO55580 |
When typing AT+IPR=XXXXX on the UART3 (UART emulated on the top of the USB stack) the target store the XXXXX speed. In case the application interrogates the target with the AT+IPR? command the target answers +IPR:XXXXX.
Such a response might destabilizes the application (its current speed let's say YYYYY and the target speed being different) |
DEVICE |
V24 |
7.4a |
| ANO55953 |
With AT&D0 configuration, the Wireless CPU® may not enter in sleep mode on DTR drop. |
DEVICE |
V24 |
7.4a |
| CUS55629 |
When the DTR drops to switch in OFFLINE mode (i.e. AT&D1 should be sent earlier), if a data write operation is pending, this operation will be canceled, and so data will be lost. |
DEVICE |
V24 |
7.4a |
| ANO53965 |
When the URL set in internal e2p is wrong, the Wireless CPU® doesn't display any +WDSI indications, or it displays a +WDSI: 4 indication (it shouldn't, no socket is opened). |
Embedded RDMS |
RDMS |
7.4a |
| ANO53978 |
When AT+WDSS=1,0 command is executed to deactivate the IDS PDP context, whereas the IDS PDP context is already deactivated. For any IDS connection done after, always returns error code 652. |
Embedded RDMS |
RDMS |
7.4a |
| ANO54089 |
On making a connection to the IDS server with the execution of the command AT+WDSS=1,1, there is a possibility of blocking the AT parser when a wrong IDS APN and a valid user APN are configured. |
Embedded RDMS |
RDMS |
7.4a |
| ANO54257 |
When a download is interrupted by the command AT+WDSS=1,0, sometimes the Wireless CPU® reconnects automatically to the server and postpones the job on the server. The download cannot be resumed anymore. |
Embedded RDMS |
RDMS |
7.4a |
| ANO54305 |
When the device is added on the server and then when the server sends a SMS bootstrap to the device, the SMS bootstrap is not treated by the device. |
Embedded RDMS |
RDMS |
7.4a |
| ANO54488 |
Using IDS services, it's possible to configure the Wireless CPU® to initiate an automatic connection to the IDS server using polling mode (see +WDSC command). If the value for the polling mode is higher than 20 minutes, the timer between two automatic connections is not a correct value and the time is shorter than required. Advice: do not use value higher than 20 for polling mode. |
Embedded RDMS |
RDMS |
7.4a |
| ANO54808 |
When a software or firmware update is launched with IDS whereas the connection was initiated by a generic alert (initiated by a monitored parameter) and a reset occurs during the download of the patch, at the next start of the Wireless CPU®, the generic alert is performed again and the update is failed. The download should be resumed. |
Embedded RDMS |
RDMS |
7.4a |
| CUS54229 |
In GPRS class CG or class B with automatic GPRS attach, when the patch download is suspended the download is resumed after few minutes which is not appropriate. |
Embedded RDMS |
RDMS |
7.4a |
| CUS54655 |
When an IDS connection is done (with AT+WDSS=1,1) and then the spy mode is activated (AT+WREGC=1), no IDS connection can be done when the spy mode is resumed (+WDSI: 7 or no response). |
Embedded RDMS |
RDMS |
7.4a |
| CUS54922 |
In CG class, when an IDS connection is failed (+WDSI: 7) and then the Wireless CPU® goes in spy mode (AT+WREGC=1), the Wireless CPU® may reset (a RTK exception occurs). |
Embedded RDMS |
RDMS |
7.4a |
| ANO55198 |
Even if the GPRS service is not attached to the MT when AT command AT+CGDATA=1 is issued, it returns CONNECT instead of +CME ERROR: 3. |
GPRS |
OTHER |
7.4a |
| CUS54682 |
Subsequent call to start a GPRS Bearer (using wip_bearerStart() or AT+CGACT=1 command) returns error (WIP_BERR_DEV), when a call to stop the previous session (using wip_bearerStop() or AT+CGACT=0,1) is followed by "AT+WAC" command. The issue is reproduced, if "AT+WAC" command is issued after stopping a bearer session and before starting a new bearer session. |
GPRS |
OTHER |
7.4a |
| CUS54758 |
Call index in the +WIND: 5,x and +WIND: 6,x is equal to 2 even if +WIND: 6,1 response has been received for the first call and the call has been disconnected. As the first call has been disconnected successfully the call index for the second call should be 1 in +WIND: 5,x and +WIND: 6,x wind responses. The issue is reproduced when ATD for the second call is made before receiving the CC_REL_IND. |
GSM |
CC |
7.4a |
| ANO54248 |
When the Wireless CPU® is registered on a cell providing only GSM service (and no GPRS/EDGE service), the auto-quadband mechanism (see +WMBS command) is not correct. The Wireless CPU® will change every time the frequencies (850/1900 <-> 900/1800) even if the GSM service is available on one frequency. The Wireless CPU® should launch the auto-quadband mechanism and should stop it when it's registered on cell. |
GSM |
OTHER |
7.4a |
| ANO55823 |
It is not possible to listen to DTMF in Rx, while playing an AMR memo in Rx. |
HWL |
AUDIO |
7.4a |
| CUS54113 |
When fast idle mode is activated, the part of the Wireless CPU® is shut down, the audio feature like DTMF cannot be used, when DTR is switch.
The correction wakes up the Wireless CPU® each time we need it (for any audio feature). |
HWL |
AUDIO |
7.4a |
| CUS54377 |
The generated DTMF tone might be distorted if using GPRS and WADS command at the same time. |
HWL |
AUDIO |
7.4a |
| CUS54770 |
The problem occurs when playing AMR memos during a voice call. If several memos are played in a row, memos after the first one may be degraded, it occurs with a 50% rate. The problem is a degradation of the memo played, onto a degradation of the voice call. |
HWL |
AUDIO |
7.4a |
| ANO54047 |
When the Wireless CPU® enters sleep mode with GSM stack (slow idle mode) and there is no network coverage, the Wireless CPU® cannot automatically retrieve network coverage i.e. considered as in sleep mode without GSM stack (slow standby mode). |
HWL |
OTHER |
7.4a |
| ANO54589 |
Using low power consumption (at+w32k=1) mode and DTR as a wake-up condition, will freeze the Wireless CPU® (no wake-up) if not network is found. |
HWL |
OTHER |
7.4a |
| ANO47516 |
Launching an Open AT® WIP application in RTE (Vc6 and Eclipse) mode for opening PPP in server mode, resets the Wireless CPU®. |
OTHER |
OTHER |
7.4a |
| ANO52295 |
TCU Capabilities indicate that no event capture or detection pin is available in fact two pins are available for the customer applications |
OTHER |
OTHER |
7.4a |
| ANO54160 |
The Wireless CPU® can reset when the customer tries to auto answer an incoming call on a closed port. |
OTHER |
OTHER |
7.4a |
| ANO54193 |
TCU Capabilities indicate that no event capture or detection pin is available in fact two pins are available for the customer applications |
OTHER |
OTHER |
7.4a |
| ANO54559 |
Reaction of 1,8V only, MEs on SIM type recognition failure, or MEs on type recognition of 3V SIMs, immediately after the ATR only the two commands "SELECT GSM" and "STATUS/GET RESPONSE" shall be send by the ME. The ME shall then deactivate the SIM/ME interface within 5 seconds and reject the SIM. However, ME sends a Select command instead of Status command and doesn’t deactivate the SIM. |
OTHER |
OTHER |
7.4a |
| ANO54588 |
The Wireless CPU® crashes when invalid melody is provided to API adl_audioMelodyPlayExt(). |
OTHER |
OTHER |
7.4a |
| ANO55499 |
When a large file is transferred through UART1 (or any physical port) there is a data loss and data corruption (some junk characters are displayed). The integrity of the transferred data is not intact. |
OTHER |
OTHER |
7.4a |
| CUS47870 |
When attempting to use simultaneously CS2 & ADD25 signals (which are multiplexed on the same pin) no error is given to the ADL application |
OTHER |
OTHER |
7.4a |
| CUS54074 |
Reading the flash memory using the pointer provided by adl_adInfo after having written data with adl_adWrite can provide a wrong result. Although the data is actually correct in flash memory, this is because of a cache memory inconsistency. |
OTHER |
OTHER |
7.4a |
| CUS55257 |
The Wireless CPU® resets when executing the SEND USSD proactive command. |
OTHER |
OTHER |
7.4a |
| CUS49814 |
When slow idle mode (AT+W32k=1) is activated and a timer with options (non strict, cyclic and rearmed on expiration) is running and the timer expires twice during sleep period, a reset occurs on Wireless CPU®. |
RTK |
TIMER |
7.4a |
| CUS50328 |
In the RTE mode, the time delay taken to invoke the call back handler of the adl_tmrSubscribe () API is 4 times more than it normally takes. |
RTK |
TIMER |
7.4a |
| ANO53243 |
Response for AT+CPWD command is not received when trying to change the SIM PIN code. Issue is faced when AT+CPWD command is given after unblocking the SIM PIN of a blocked SIM by using SIM PUK and AT+CPIN command. |
SIM |
OTHER |
7.4a |
| ANO55164 |
When we issue AT+CPIN=11111111,3699 and AT+CPIN2=22222222,5678 consecutively, then the module enters busy state indefinitely. |
SIM |
OTHER |
7.4a |
| ANO55402 |
The internal SIM cannot be selected in SIM_EXT_PREFFERED mode |
SIM |
OTHER |
7.4a |
| CUS54707 |
Some SIM may not be powered on due to which AT+CPIN commands always return +CME ERROR:10. |
SIM |
RESET |
7.4a |
| CUS54540 |
At high speed of 104 MHz, the Wireless CPU® is in a state where it is switched off immediately when ON/OFF pin is set to OFF, the auto-maintain mechanism doesn't work. |
SYS |
INIT |
7.4a |
| ANO53326 |
The OPEN AT® application using old Task Init "wm_apmCustomStackSize" can fail on start-up, when u16 value just given after address of wm_apmCustomStackSize differ from 0 (linker dependent). |
SYS |
INIT |
7.4 |
| ANO52754 |
Data abort happens if an external interrupt occurs (on FIQ) when an ADL functions is called. |
SYS |
ISR |
7.4 |
| ANO52210 |
Stuck in command mode after +++ when using UART PPP bearer. |
OTHER |
OTHER |
7.4 |
| ANO52243 |
wip_netExit () API does not release the memory resources allocated by the API wip_netInit () successfully. Memory leak can be observed by debugging the Open AT® application in remote mode. |
OTHER |
OTHER |
7.4 |
| ANO53645 |
User controlled PLMN selector list is not taken into account because the list was added into the wrong address. |
OTHER |
OTHER |
7.4 |
| CUS53833 |
Impossible to perform a call when the spy mode is left. |
GSM |
MM |
7.4 |
| ANO52830 |
Using IDS services, the customer application can request a user agreement before downloading any update package. In this state, when the Wireless CPU® is not registered to the network and when the customer application accept to download the update package using +WDSR command, the Wireless CPU® returns an OK response but the download is not launched. The Wireless CPU® should return an error (+CME ERROR: 651) in this case because it is not possible to launch the download. |
Embedded RDMS |
RDMS |
7.4 |
| ANO52948 |
When the inserted SIM supports the PLMNwAct SIM file (user preferred PLMNs with access technologies), getting it using IDS services is not possible. The Wireless CPU® sends an empty list to the IDS server. This list is well sent to the IDS server when the SIM support the PLMNSel SIM File. The user preferred PLMN list should always be sent to the IDS server whatever the inserted SIM |
Embedded RDMS |
RDMS |
7.4 |
| ANO53180 |
Using IDS server, the IDS server can update the APN used for the IDS PDP context on the Wireless CPU® by sending a SMS (Sent APN feature on the IDS Web portal). If this SMS is sent to the Wireless CPU® before its registration on the server, this SMS is well treated. If this SMS is sent to the Wireless CPU®(r) after its registration on the server, this SMS is not treated. This SMS should be treated in all cases. |
Embedded RDMS |
RDMS |
7.4 |
| CUS53562 |
When a WIP session is in progress and an IDS session occurred, the end of the IDS session (deactivation of the PDP context) provoke an error on WIP interface ( WIP_CERR_NETWORK_UNREACHABLE occurred) |
Embedded RDMS |
RDMS |
7.4 |
| ANO53573 |
If the command AT+WDSS=1,0 is done just after the response of AT+WDSS=1,1 command, the Wireless CPU® may reset |
Embedded RDMS |
RDMS |
7.4 |
| ANO53597 |
When an error occurs during a PDP context activation (the error must be different from a bad NAP configuration), the AT+WDSS command does not respond. |
Embedded RDMS |
RDMS |
7.4 |
| ANO53672 |
Using IDS services, an Open AT® application can subscribe to monitoring mechanism. This application can configure the monitoring for each own parameter. When a trigger is configured and when this trigger is reached, the device makes a reset and the automatic report is not sent.
The device should not reset and send the automatic report to the IDS server. |
Embedded RDMS |
RDMS |
7.4 |
| ANO53703 |
Using IDS services, parameters can be configured to send automatic report to the IDS server when a triggered value is reached. Moreover, a hysteresis can be configured. If this value is negative, the Wireless CPU® changes it to positive value (-9 is replaced by +9). The Wireless CPU® should not change the value sign! This implies that automatic report on hysteresis is not available |
Embedded RDMS |
RDMS |
7.4 |
| ANO53704 |
Using IDS services, parameters can be configured to send automatic report to the IDS server when a triggered value is reached. Moreover, a hysteresis can be configured. If this value is equal to 0, the Wireless CPU® does not take into account this value. This implies that automatic report on hysteresis is not available. This mechanism should be available |
Embedded RDMS |
RDMS |
7.4 |
| CUS53371 |
Wireless CPU® reset occurs during Edge transfer on IDEA network using WIP. |
EGPRS |
RLC |
7.4 |
| CUS52847 |
When reading on I2C bus in a loop, Wireless CPU® freezes. |
DEVICE |
IOB |
7.4 |
| ANO52254 |
The function adl_busSubscribe () for the parallel bus does not work properly when selecting the CS2. |
AT |
OTHER |
7.4 |
| ANO53017 |
According to 3GPP 27.007 specifications, it should be possible to indicate an access technology in a user preferred PLMN using +CPOL command if the SIM support the PLMNwAct file. It's possible to read PLMNs with access technology but it's not possible to add a PLMN with an access technology |
AT |
OTHER |
7.4 |
| ANO53212 |
When we enable the OFFWHENUNPLUG feature and allocate any external interrupt to trigger the Wireless CPU® power off, then when the state of the external interrupt changes the Wireless CPU® is not powered off. |
AT |
OTHER |
7.4 |
| ANO53793 |
PTCRB 27.16 test is failed when SIM returns a Memory Problem error in a message. The Wireless CPU® should return a dedicated response to the command. In this test, +CPBW command is used to add a phonebook entry in the SIM phonebook but no response is returned. In this test, a +CME ERROR: 13 response should be returned |
AT |
OTHER |
7.4 |
| ANO53811 |
The +CPOL? command allows an application to list PLMNs entries present in different SIM files. When +CPLS command is set to 0 (default value), entries listed by AT+CPOL? command are the ones present in PLMNwAct file or PLMN_SEL file. (If PLMNwAct is not present, PLMN_SEL file will be selected). If these 2 files are not present, AT+CPOL? makes a reset. +CPLS default value should be set according to SIM files presence. If no PLMN SIM files are allocated in the SIM, AT+CPLS? will return +CME ERROR: 3 |
AT |
OTHER |
7.4 |
| ANO53868 |
SIM file 6F60 cannot be updated by AT+CPOL command because wrong record size is set. Record size 3 is used instead of 5. |
AT |
OTHER |
7.4 |
| CUS53660 |
Updated phone number is not displayed using AT+CPBR command, in case the user updates a phone number in the phonebook having adjacent 0's with a phone number such that the adjacent 0's are still in place before the first difference. The phone number is updated by removing the SIM, updating in another phone and then inserting the SIM again in the Wireless CPU® |
AT |
PHONEBOOK |
7.4 |
| CUS41702 |
When "ME" are selected for SMS storage and read memories, when the Wireless CPU® receive a concatenated SMS which contains a UDH (user data header) and data in UCS2 format, and when the text length of this message is odd, the PDU string returned to the application, using AT+CMGR command, is incorrect. |
AT |
SMS |
7.4 |
| CUS51817 |
When a SMS-PP data download is received by the Wireless CPU®, the SIM may ask a refresh with a SIM reset. The Wireless CPU® sends a detach to the network before the network acknowledges the SMS transmission. |
AT |
STK |
7.4 |
ANO52361 and
ANO52367 |
Second FAX call cannot be handled due to there is no terminal response send from ATI to OPEN AT®. This cause further AT commands initiate by ADL are saved in the stack waiting for the answer of first ATA command. ATI should send a terminal response to OPEN AT® with a new flag, so that OPEN AT® can unblock the queue and the terminal response will not be displayed in the terminal. |
AT |
OTHER |
7.3a |
| ANO47511 |
When 2 PPP sessions are opened on USB and UART1 (or UART2), when the USB session is released, the session on UART1(or UART2) is also released, it should not. |
AT |
OTHER |
7.3a |
| ANO52150 |
Resuming a suspended Open AT® application using an interruption is no more available from R61 FW version. |
AT |
OTHER |
7.3a |
| ANO52208 |
Wireless CPU® can reset in idle task (generally after starting). |
AT |
OTHER |
7.3a |
| ANO52253 |
When a Nitz message is received with a negative local time zone, the computer hour is wrong (in the case of the automatic time zone update is set with the +CTZU command) |
AT |
OTHER |
7.3a |
| CUS52297 |
If an outgoing CSD call is first accepted and then disconnected by the peer before receiving the CONNECT indication, further ATD commands from the Wireless CPU results in "+CME ERROR: 536". The call should be allowed and the error should not be received. |
AT |
OTHER |
7.3a |
ANO49881 and
ANO50507 |
DTMF blank duration corrupted if user change its value during Wireless CPU® is in airplane mode. |
AT |
OTHER |
7.3a |
| ANO51564 |
The unsolicited responses after the Wireless CPU® is powered off are not completely received by the customer application.
For example, if "AT+WIND=255" and "AT+CREG=1" are set before, once the Wireless CPU® is powered off (as described in "How to reproduce it" field), the unsolicited response "+WIND: 8" and "+CREG: 0" are not sent. |
AT |
OTHER |
7.3a |
| ANO52152 |
Under atlas environment, after CPIN and AT++CMEE=1 commands are entered, AT+WDSA="" returns OK instead of +CME ERROR 3. |
AT |
OTHER |
7.3a |
| ANO52156 |
Using +WDSH command, it is possible to define some host application in order to use IDS services for these applications. Declaring a host application when the IDS service is not in ACTIVATED state (see +WDSG command) makes a reset. This command should be allowed even if IDS services are in DEACTIVATED or TO BE PROVISIONED states. |
AT |
OTHER |
7.3a |
| CUS52329 |
H command allows the application to release calls. This command accepts a parameter (which is 1 or 2). If this parameter is different from 1 and 2, the Wireless CPU® does not return any response and all commands sent to the Wireless CPU® on the same port will always return +CME ERROR: 515 response. +CME ERROR: 3 should be returned to ATHx command with x different from 1 and 2 and should not block the port in +CME ERROR: 515 state |
AT |
OTHER |
7.3a |
| ANO51610 |
RI signal is pulsed when +WBCI unsolicited event occurred and +WRIM bit 14 is set instead of bit 6. |
AT |
OTHER |
7.3a |
| CUS49475 |
When using the command +CPBW, the value of TON/NPI only allows 145 and 129. We need to support range from 128 to 255.
Therefore, the actual definition of <type> should be:
<type>: integer type; Type of address octet. (refer GSM 04.08 sub clause 10.5.4.7)
129 ISDN / telephony numbering plan, national / international unknown
145 ISDN / telephony numbering plan, international number
161 ISDN / telephony numbering plan, national number
128 - 255 Other values refer GSM 04.08 section 10.5.4.7 |
AT |
PHONEBOOK |
7.3a |
| ANO52417 |
+CMS ERROR: 538 is displayed when we try to copy all the messages in Flash to SIM. The SMS of the same replacement type are present in Flash and SIM memory. Also, for reproducing the issue the number of free locations in SIM SMS memory should be less than the number of messages to be copied from Flash. |
AT |
SMS |
7.3a |
| CUS52869 |
Some junk characters are displayed in the +CMT indication in case the +CMT indication is enabled by the command AT+CNMI=2,2 on receiving a SMS. |
AT |
SMS |
7.3a |
| ANO52251 |
After an UART3 opening and closing sequence, it is not any longer possible to open the UART3. Consequently customer applications opening UART3 should never close it. |
DEVICE |
USB |
7.3a |
CUS52740 and
CUS53006 |
Using FCM API in Open AT® application, no flow control configuration is set on the associated UART, receiving data on UART and having a lot of Wireless CPU® load on data reception makes the Wireless CPU® reset. |
DEVICE |
V24 |
7.3a |
ANO51974 and
ANO52009 |
User data cannot reach TMT/TE in FCM data mode. |
DEVICE |
V24 |
7.3a |
| ANO51128 |
When an OPEN AT® parameter is provisioned, a reset can occur. |
Embedded RDMS |
RDMS |
7.3a |
ANO51347 and
ANO52164 |
Open AT® application may not be able to subscribe to 50 parameters for IDS monitoring. That is due to a memory overconsumption and it depends on Application use cases. A reset will occur once the limit is reached. A possible workaround is to prefer the use of integer type parameters and if necessary to subscribe to buffer type parameters at the end of parameters subscription phase. |
Embedded RDMS |
RDMS |
7.3a |
ANO52232 and
ANO53072 |
When the SMS bootstrap are received to provision the NAP, the Wireless CPU® resets. |
Embedded RDMS |
RDMS |
7.3a |
| ANO52482 |
When a power off is made and the protocol stack is "hot" reset using AT+CFUN=1,0, the device can register to the network but no connection to the IDS server is available. |
Embedded RDMS |
RDMS |
7.3a |
| ANO52495 |
Using IDS service, it is possible to configure a parameter in order to send an alert to the IDS server when a specific value is reached. If the triggered value is reached when the Wireless CPU® is not registered on the network, the automatic report will be sent when the Wireless CPU® is registered again on the network. However, the reported value is the current one (the last updated value). So if the parameter value was changed between the moments when the triggered was reached and the report, the reported value is not the right one. The reported value should be the value when the triggered was reached. |
Embedded RDMS |
RDMS |
7.3a |
| ANO52497 |
When a device is created in the IDS server, according to the device model used for the creation, a SMS can be sent to the device in order to provision the APN to be used by the Wireless CPU® in order to make a connection to the IDS server. This SMS is not treated by the Wireless CPU® and stored in SIM. This SMS should be treated, should not be stored in SIM and no indication should be returned by the Wireless CPU® to indicate that this SMS was received. Then the APN for IDS services should be updated (see +WDSS command). |
Embedded RDMS |
RDMS |
7.3a |
| ANO52585 |
Using IDS services, it is possible that the Wavecom IDS server schedules a job in order to allow the device to make a connection to a 3 rd party server (and so the device won't make anymore a connection to the Wavecom IDS server).
When the device is configured to make a connection to a 3rd party server to use IDS services and not to make a connection to the Wavecom one, it should be possible for the 3rd party server to update the embedded credentials in the device. This mechanism uses a generated signature which should be checked by the SW public key which is embedded in the device. Using a 3rd party server, this signature was checked by the device using the FW public key and not the SW public key. The right public should be used. |
Embedded RDMS |
RDMS |
7.3a |
| ANO52583 |
Using IDS services, upgrading a device from FW7.2 to FW7.3 and if a monitoring on timer on MO Call or MT call is configured in the device, after the FW2.20 install, the device makes a reset each time the monitoring timer happens. This reset should not happen. |
Embedded RDMS |
RDMS |
7.3a |
| ANO51412 |
Using IDS services, the Wireless CPU® makes a connection to the IDS server after an update to acknowledge the install status. If a periodic report for a monitored parameter is scheduled on the Wireless CPU® and if an install status should be sent at the same time, the connection to the IDS server fails and then the install status is never sent to the IDS server. The Wireless CPU® should always send the install status. |
Embedded RDMS |
RDMS |
7.3a |
ANO52891 and
ANO52984 |
When an update is done for R72a00 ->R73_00->R73a00, the last update (R73a00) is not done. The Wireless CPU® is always with the R73_00 . This issue can occur when an update is in progress and a reset occur between the end of the downloader and the call of the update agent. |
Embedded RDMS |
RDMS |
7.3a |
| ANO53251 |
Using IDS server, the IDS server can update the APN used for the IDS PDP context on the Wireless CPU® by sending a SMS (Sent APN feature on the IDS Web portal). If this SMS is sent to the Wireless CPU® before its registration on the server, this SMS is well treated. If this SMS is sent to the Wireless CPU® after its registration on the server, this SMS is not treated. This SMS should be treated in all cases. |
Embedded RDMS |
RDMS |
7.3a |
ANO52060
and
ANO52354 |
When the objects have been removed, the NAP is also erased but it shouldn't. |
Embedded RDMS |
RDMS |
7.3a |
| ANO52138 |
When the user try to monitor Open AT® parameters using the triggers, the mechanism is not working (no generic alert are sent when the trigger are reached). |
Embedded RDMS |
RDMS |
7.3a |
| ANO52233 |
Sometimes, during a connection to the IDS server, some errors can occur because of the network. The device could relaunch the connection in these cases. |
Embedded RDMS |
RDMS |
7.3a |
| ANO51897 |
The actual monitoring of network coverage increases when the Wireless CPU® is in limited services (emergency) or full services (register on a network). It should be only increases when the Wireless CPU® is in full services (and decrease otherwise) |
Embedded RDMS |
RDMS |
7.3a |
ANO50378
and
ANO52379 |
Using IDS service, when the server requests the Preferred PLMN list or set a Preferred PLMN, the format parameter of +CPOL command is set to numeric.
When the Preferred PLMN is updated or read by the IDS server, the format parameter of +CPOL command should not be set to numeric. |
Embedded RDMS |
RDMS |
7.3a |
| ANO50379 |
Using Device services, when the IDS server gets the Preferred PLMN list, if the format parameter of +CPOL is not set to 2 (numeric), the response to the server request is an error. If the format parameter of +CPOL is set to 2 (numeric), the preferred PLMN list is well returned by the Wireless CPU®. The Wireless CPU® should send the list in all cases. |
Embedded RDMS |
RDMS |
7.3a |
| ANO50870 |
When an IDS session is active, the response to AT+WDSS? Doesn’t display the login and password. |
Embedded RDMS |
RDMS |
7.3a |
ANO52181 and
ANO52302 |
Using IDS services, the IDS server can get the MO and MT voice call error counters in roaming. In this data, a history is present for each VPLMN on which an error was occurred on voice call. If the error is due to an antenna disconnection, the PLMN created in the history is filled with MCC=000 and MNC=00 instead of the real values. The Wireless CPU® should fill this value with the last registered PLMN details. |
Embedded RDMS |
RDMS |
7.3a |
| ANO52275 |
Using IDS services, it's possible to monitor the battery level of one or several devices. An automatic report can be requested if the battery level reaches a specific value. If this value implies an automatic power off of the device (+WBCI: 0 indication is then returned by the Wireless CPU®), the automatic report is not sent to the IDS server at the next network registration. This automatic report should be sent to the IDS server. |
Embedded RDMS |
RDMS |
7.3a |
ANO52580
and
ANO52581 |
When an IDS session is active, the response to AT+WDSS? doesn't display the login and password |
Embedded RDMS |
RDMS |
7.3a |
ANO48769
and ANO49273 |
Incomplete resilience of the AD volume re-compaction process to unattended resets or power losses. |
FLASH |
DOTA |
7.3a |
| ANO52513 |
Using IDS services, the Wireless CPU® makes a connection to the IDS server after an update to acknowledge the install status. If a periodic report for a monitored parameter is scheduled on the Wireless CPU® and if an install status should be sent at the same time, the connection to the IDS server fails and then the install status is never sent to the IDS server. The Wireless CPU® should always send the install status. |
GPRS |
OTHER |
7.3a |
| ANO49857 |
Wireless CPU® sends a NO CARRIER indication instead of OK response in case GPRS session is terminated by DTR drop. |
GPRS |
OTHER |
7.3a |
| CUS52932 |
Effective application stack size is down casted into a 16-bit integer when a stack size of more than 64k is given in the "adl_InitTasks_t" tasks declaration. |
OTHER |
OTHER |
7.3a |
| ANO52212 |
Wireless CPU® resets if we send through OPEN UART more bytes than the buffer size allocated for the read action |
OTHER |
OTHER |
7.3a |
| CUS52838 |
When write operations are triggered periodically the OnTxComplete event handler is sometimes not recalled. Consequently the pending write operation never ends. |
OTHER |
OTHER |
7.3a |
| CUS49913 |
When the target is camped on a PLMN and a continuous data flow is sent to UART1 or UART2 without any flow control and Open UART is used to manage this data flow in reception, it may lead to a target reset. |
OTHER |
OTHER |
7.3a |
| ANO51210 |
When UART1 or UART2 is directly used by an Open AT® application with flow control option disabled at speeds greater than 57600 bps and the target is camped on a PLMN data loss (in reception way) may occur. |
OTHER |
OTHER |
7.3a |
| ANO51919 |
After starting an Open AT® application Wireless CPU® may reset in idle task. |
OTHER |
OTHER |
7.3a |
| ANO47039 |
The InitType of adl_main after the reset doesn't indicate ADL_INIT_REBOOT_FROM_EXCEPTION for API adl_errHalt (). |
OTHER |
OTHER |
7.3a |
| ANO51170 |
If flash objects need to be deleted we have to use AT+WOPEN=3.
This command always returns ERROR 548 "No flash objects to delete" even if a flash object exist. |
OTHER |
OTHER |
7.3a |
| ANO52079 |
Attempting to gather UART1 or UART2 capabilities by using io_control operation is not functional. However user application is allowed to gather this information at the opening stage by filling in the capabilities field of the sUartSettings_t structure which shall be provided to the adl_odOpen function. |
OTHER |
OTHER |
7.3a |
| CUS53192 |
No response to AT+CPWD command, after the GPRS context is activated and ATI automation freezes. |
SIM |
OTHER |
7.3a |
| CUS52562 |
When a SIM card doesn't respond, a fatal error occurs after approximately 2 hours, the Wireless CPU® resets. |
SIM |
OTHER |
7.3a |
| CUS52256 |
After a SIM refresh, the proactive polling command for the SIM presence detection is not sent anymore |
SIM |
STK |
7.3a |
| CUS50308 |
Wireless CPU® may not wake up or may not stop after the "AT+CPOF" command when an alarm is used |
SYS |
OTHER |
7.3a |
| ANO51206 |
When an application, using ADL event service, is running RTE mode, an error message is raised about RPC protocol. |
OTHER |
OTHER |
7.3 |
| ANO50891 |
When the command "AT+WASR?" is executed on the WMP50, invalid GPIO (GPIO24) is returned, as the GPIO range of WMP50 only supports GPIO0 to GPIO10. |
OTHER |
OTHER |
7.3 |
| ANO50081 |
ADL application cannot set the UART (1 or 2) speed to 921600 bps by using the UART_RATE_921600 enumerated provided in the wm_uart.h header file. |
OTHER |
OTHER |
7.3 |
| ANO50063 |
When we use the adl_audioTonePlay API to play a single tone, (by setting the second frequency equals 0), the Wireless CPU® return the ADL_RET_ERR_PARAM error. |
OTHER |
OTHER |
7.3 |
| CUS49911 |
Wireless CPU® can reset when a lot of bytes are being sent on UART and the AT+CPOF command is received from one port |
OTHER |
OTHER |
7.3 |
| CUS50988 |
It is not possible to play a tone using adl_audioTonePlay () with a second gain equals 0 |
OTHER |
OTHER |
7.3 |
| CUS49914 |
TMT always displays incorrect backtraces when a fatal error or an exception occurs or replayed from flash memory. |
OTHER |
OTHER |
7.3 |
| CUS52195 |
Interrupts (e.g. SPI or External IRQ pin) could interfere with Open AT® tasks initialization. This could result in an increase of one Open AT® task stack usage. |
OTHER |
OTHER |
7.3 |
| CUS51216 |
When the PLMN name search using E-ONS is activated by AT+WOPN=4,31 and if the inserted SIM contains PNN and OPL files related to E-ONS feature, the PLMN name returned by the Wireless CPU® can be wrong if in OPL files, the D character (wild card) is used for the MNC code only (and not for the MCC code). The Wireless CPU® should well manage this case and return the correct PLMN name. |
SIM |
OTHER |
7.3 |
| CUS49537 |
The ADL software watchdog timer seems to be inaccurate when a software watchdog reset is triggered |
SYS |
OTHER |
7.3 |
| CUS51801 |
CME ERROR 13 is sometimes received when using SPI or UART. |
SYS |
OTHER |
7.3 |
| DEV50851 |
The MS may perform a non-optimized PLMN selection, since it may not use the list of Equivalent PLMNs provided by network operators. |
UMTS |
PLMN_SEL |
7.3 |
| ANO49389 |
Reset can occur when a call disconnection is performed while a handover procedure is on progress. |
GSM |
RR |
7.2a |
| CUS49525 |
When an Open AT® Application tries to write in FLASH, if another task is scheduled which modifies the FLASH space memory, then adl_flhWrite() function may return ADL_FLH_RET_ERR_MEM_FULL or ADL_FLH_RET_ERR_NO_ENOUGH_IDS error |
OTHER |
OTHER |
7.2a |
| CUS49667 |
Packet PDCH Release wrongly managed during two phases access. This case leads in a GPRS blocking state. |
GPRS |
OTHER |
7.2a |
| ANO49979 |
DTMF detection is not available when the Wireless CPU® is not synchronized to the network (used in Audio Diagnosis mode) |
(None) |
(None) |
7.2a |
| CUS50008 |
Response of ATA command is not received when the ATA and call disconnection(ATH) command at the peer end are issued simultaneously after a successful call is made and hooked. The issue is reproducible when before receiving a call confirmation message from the network at the called end the call is disconnected from the calling end. Also the response to the next AT command includes the buffered response for ATA command which was not received. |
AT |
OTHER |
7.2a |
| ANO49255 |
Wireless CPU® registers to a wrong PLMN after recovering from No service state during a GPRS transfer (it was manually registered previously). |
AT |
OTHER |
7.2a |
| ANO49789 |
When an Open AT® Application subscribes to a provisioned parameter using IDS services, when the server gets the provisioned value, callbacks for getting length and getting data are called twice. It should be better to call 2 times the callback for data length (in order to well allocate memory) and call only one time the callback to get data. |
Embedded RDMS |
RDMS |
7.2a |
| ANO50011 |
The Location Area Code (LAC) of the cell on which the Wireless CPU® is camped on, is wrongly displayed when using the Radio Spectrum Monitoring channel interface for Open AT® Applications. |
OTHER |
OTHER |
7.2a |
| ANO50052 |
Using IDS services, if the IDS server tries to get the preferred operators list stored in the SIM using the provisioning mechanism, the WIRELESS CPU® can return a truncated list if at least one unknown operator code exists in this list. An unknown operator is an operator code which is not associated to a long and a short name in all memories storage for operator names (see +WOPN command for more details). The WIRELESS CPU® should return the whole list even if the operator name is unknown. |
Embedded RDMS |
RDMS |
7.2a |
| ANO49916 |
Activating +ILRR notifications (AT+ILRR=1), being in Autobaud mode (AT+IPR=0) and having a CSD call established (ATD... or ATA => CONNECT), then the +ILRR intermediate response does not notify upon the current UART speed : it reports Autobaud mode (+ILRR:0) whereas it should report the current speed (e.g. at 115200 Bauds/s +ILRR: 115200). |
AT |
OTHER |
7.2a |
| CUS49937 |
When an Open AT application closes all the physical ports, after a reboot, the SIM full initialization event is never received in the Open AT® application, and the SIM state remains "ADL_SIM_STATE_INIT". |
AT |
OTHER |
7.2a |
ANO49965and
ANO49966 |
After a upgrade using DOTA2, the Open AT® application present in the Wireless CPU® does not start (AT+WOPEN? returns "+WOPEN: 0"). Ideally, after the DOTA process, the WOPEN state should not change and the application should start. |
OTHER |
OTHER |
7.2a |
| ANO48794 |
+CME ERROR:3 is presented for a valid pin code following steps:
1) Download the MCC list allowed E2P file to the Wireless CPU®.
2) Activate CNL lock on Network1 (MCCMNC1) and Network2 (MCCMNC2) by AT+WLCK.
3) Insert Network1 SIM and enter pin code, can make a call.
4) Insert Network3 SIM (MCCMNC3) and enter pin code, fail to make a call. It is expected behavior.
5) Insert Network4 SIM (MCC not contained in MCC List allowed) and enter pin code, display SIM NOT ALLOWED FOR THIS MODULE. It is expected behavior.
6) Insert Network1 SIM and enter pin code by AT+CPIN, the response is +CME ERROR: 3, it should be "OK". |
SIM |
OTHER |
7.2a |
ANO48947 and
ANO50323 |
When attempting to modify the preferred operator list using the "AT+CPOL" command, the user is prompted with +CME ERROR: 13, which is the correct behavior. However after this
1.When the PLMN list is read using the "AT+CPOL?" command, instead of the old values, the new values attempted to write are returned. Ideally, since the attempted write failed, the read command should return the old values.
2. Second or any further attempt to use "AT+CPOL" write command returns "OK" instead of "+CME ERROR: 13".
3. AT+COPS command returns "+CME ERROR: 13" instead of the normal functionality. |
AT |
OTHER |
7.2a |
| CUS50362 |
DOTA and IDS updates fail if a special volume configuration is set in the production bench (typically for Q268x with integrated flash). Downloader update cannot be performed by 1K-XModem. A workaround consists in configuring again A&D volume from Open AT® Application |
DWL |
Other |
7.2a |
| ANO50118 |
If an unauthorized SIM has been inserted once, the WIRELESS CPU® is blocked in +CME ERROR: 515 error state after pin code is entered but network lock is activated for a network lock SIM. If an unauthorized SIM and then a valid SIM 1 have been inserted, the SIM status does not update after inserted a valid SIM 2. The SIM status kept in valid SIM 1 and can make a call. |
AT |
Other |
7.2a |
| DEV50051 |
When a RDMS context activation is asked during a RDMS context deactivation, it is not possible to activate this context anymore |
Embedded RDMS |
RDMS |
7.2a |
| CUS49803 |
Since Oasis2, when a GPRS session is opened using windows dialup, the server IP address is 0.0.0.0 if it was not received during the connection establishment. It was 192.168.111.111 in older version. |
AT |
OTHER |
7.2a |
| DEV49760 |
RTE stability enhancement |
OTHER |
OTHER |
7.2a |
| ANO44449 |
Remote SIM is not accessible after OSA subscription is done. |
SIM |
OTHER |
7.2a |
| CUS50421 |
With OSA application the WMP100 resets if the SIM is absent from the rack. |
SIM |
OTHER |
7.2a |
| CUS50359 |
The Wireless CPU® is not able to register to the network when using SIM cards with missing EFad file.
The Wireless CPU® should be able to register to the network even if the EFad file is missing from the SIM card. |
GSM |
PLMN_SEL |
7.2a |
ANO50250 and
ANO50251 |
IDS Server interface display of monitored value is incorrect |
Embedded RDMS |
RDMS |
7.2a |
| ANO50342 |
On WMP50, when the IDS server gets the embedded version, a useless space is returned at the data end. This space should not be returned by the WIRELESS CPU®. |
Embedded RDMS |
RDMS |
7.2a |
| ANO49504 |
When trying to connect to the server with a specific SIM card (Smartone-Vodafone), the network seems to send some cookies, the connection to the IDS server failed. In this case, the Wireless CPU® should proceed with the connection. |
Embedded RDMS |
RDMS |
7.2a |
| ANO50537 |
When a generic alert is done and an update job is present at this moment on the IDS server, the job will be executed. After the download and before the call of the update agent, a reset occurs, the patch is not installed. The job should be well executed. |
Embedded RDMS |
RDMS |
7.2a |
| ANO50422 |
[IDS] When the data monitoring values present in a generic alert are too long, the wbxml string is badly formatted. |
Embedded RDMS |
RDMS |
7.2a |
| ANO50714 |
If the communication socket is closed during a session, the session fails. But the device is supposed to re-open the socket and finish the session. |
Embedded RDMS |
RDMS |
7.2a |
| ANO50857 |
Using IDS services, if the package install is automatic (default behavior and see +WDSC command) and if the battery is removed between the package download end and before the install, the install won't be launch at the next start up. Because the install is in automatic mode, the install should be launched at the next start up. |
Embedded RDMS |
RDMS |
7.2a |
| ANO47737 |
On Q64 Wireless CPU®, when an Open AT® application is under execution and "+CMT" indication is activated (AT+CNMI=2,2), the +CMT indication is not received after sending an SMS. |
AT |
SMS |
7.2a |
| CUS49914 |
TMT always displays incorrect backtraces when a fatal error or an exception occurs or replayed from flash memory. |
OTHER |
OTHER |
7.2a |
| ANO50994 |
A reset occurs when several SIM insertion/extraction are done when RDMS credentials are present |
Embedded RDMS |
RDMS |
7.2a |
| ANO47185 |
The day field of the AT+CCLK command is always set to zero instead of range (1-to-7) during the error case. Because of this, when an alarm is set using AT+CALA command to a date different from the current date, the alarm does not occur. |
AT |
OTHER |
7.2 |
| ANO40743 |
The Wireless CPU® resets in the following scenarios:
- When "ME" extended phonebook entry is read using AT+CPBN or AT+WPGR command with selected phonebook as "MT".
- When "ME" extended phonebook entry is read using AT+WPGR command with selected phonebook as "SM". |
AT |
PHONEBOOK |
7.2 |
| CUS47597 |
When the user sets the phonebook characters to Hex or custom mode with +WPCS and saves the configuration with AT&W, the Wireless CPU® always reboots after the execution of AT+STGI=0. |
AT |
STK |
7.2 |
| ANO41985 |
When a setup call proactive command is performed using the command "AT+STGR=4,1" to get the billing information and the call is released before the connection, no terminal response is sent to the SIM. |
AT |
STK |
7.2 |
| CUS41988 |
When CMUX protocol is launched on one port and auto answer is set using ATS0 command on a logical port, during an incoming call, the Wireless CPU® resets. The Wireless CPU® should not reset and the incoming call should be automatically accepted. |
DEVICE |
CMUX |
7.2 |
| ANO47032 |
When using the opcode and/or address fields of the SPI bus API, a freeze may occur. E.g. using Ethernet over SPI driver, the Ethernet bearer stucks after few minutes. |
DEVICE |
IOB |
7.2 |
| ANO47298 |
The IDS feature doesn’t work with a delta patch having size greater than 65kB. Erratic reset is observed during the installation of 64KB+ update packages |
N/A |
N/A |
7.2 |
| ANO48668 |
It is not possible to manage 2 devices (using CS2 and CS3) on the parallel bus. |
OTHER |
OTHER |
7.2 |
| ANO41814 |
When an Open AT® application is running, after a reset (AT+CFUN=1), +WIND: 0/13/13/14 indications are sent to the external application, even if the application has not configured the WIND indication by AT+WIND=<value>. These indications should not be sent to the external application (only internal to Open AT® ). |
AT |
OTHER |
7.1b |
| ANO44408 |
After entering the correct PIN code, when a forbidden PLMN is selected using AT+COPS=1,2,xxxx, the selection fails with the error code - +CME ERROR: 547 (Emergency call is allowed without SIM). Instead, the error code +CME ERROR: 32(Network not allowed-Emergency call only) should be displayed. |
AT |
OTHER |
7.1b |
| CUS41983 |
In 14,4 kbits V.110 connection (+CBST: 75,0,1), the CONNECT response is not sent as DATA but as AT intermediate response. Because of which, in 7E1 framing, the CONNECT string is not in the right format (framing issue). The CONNECT response should be correctly returned by the Wireless CPU® and in the right framing. |
AT |
OTHER |
7.1b |
| ANO41995 |
When an Open AT® application sets the auto answer using ATS0 command, the Wireless CPU® resets when an incoming call is automatically accepted. This reset does not happen when the auto answer is activated by an external application. The Wireless CPU® should not make a reset and the incoming call should be automatically accepted. |
AT |
OTHER |
7.1b |
| CUS42010 |
When “AT+WOPEN=6” command indicates zero A&D memory size (for example “+WOPEN: 6,0,832”), it is not possible to perform DOTA anymore on the Wireless CPU®. |
AT |
OTHER |
7.1b |
ANO48217 and
ANO48328 |
Sometimes, when a windows remote network connection is released, it is not possible to open a new session anymore when the disconnection is detected by the DTR (ATD*99***1# responds +CME ERROR: 3). After some time, opening a new session is possible. |
AT |
OTHER |
7.1b |
| ANO48218 |
When a GPRS session is activated and when the &D configuration is set to 2, dropping the DTR signal releases the GPRS session but NO CARRIER indication is not returned by the Wireless CPU®. This indication should be returned. |
AT |
OTHER |
7.1b |
| ANO41393 |
- Response to the AT+CLCC command is not correctly displayed in case there is no alpha field associated with the number or the number is not stored.
- An extra byte is appended in the response string for AT+CLCC if HEX character set is selected and the string is not UCS2.
- In case if a UCS2 string starts with "90", the alpha field displayed with AT+CLCC is not correct. |
AT |
OTHER |
7.1b |
| CUS41975 |
When the current call list is read by “AT+CLCC”, if a current call name is in UCS2 format and a "00" is present within UCS2 byte string, the current call name display is wrong and stopped at first appearance of "00". |
AT |
OTHER |
7.1b |
| CUS41977 |
When two calls are active, an extra 0x00 byte appears at the end of Name field of second call. This happens when character set is HEX. |
AT |
OTHER |
7.1b |
| CUS41979 |
When a GPRS session is launched using ATD*99***1# or +CGDATA command and session is deactivated using +CGACT command during GPRS transfer, the response to the +CGACT command is not returned by the Wireless CPU®. The response should be returned and the GPRS session should be terminated. |
AT |
OTHER |
7.1b |
| CUS41994 |
When the character set used by the TE is set to CUSTOM using the AT+CSCS="CUSTOM" command, the USSD messages received by the Wireless CPU® are not displayed in accordance to the CUSTOM character set. |
AT |
OTHER |
7.1b |
| CUS42524 |
When the self-diagnostic activation mode is activated (with AT+WDIAG=1,1,1,0,0,0) and 0v is supplied to the AUX-ADC pin, the diagnostic unsolicited indications are stopped (no +WDIAG indication received). |
AT |
OTHER |
7.1b |
| CUS45313 |
Value of +CRSL command changed when performing an outgoing call if traffic channel is not allocated. |
AT |
OTHER |
7.1b |
| CUS46072 |
No call possible if the Kc file is missing or corrupted in the SIM |
GSM |
MM |
7.1b |
ANO44547 and
ANO47409 |
If a SIM supports CPHS file and if a mail box number (6F17 SIM file) is composed of more than 20 digits (so EXT1 SIM file is used), the whole number is not returned using AT+CPHS=2,2 command but it's truncated to 20 digits. The complete number should be returned. |
AT |
OTHER |
7.1b |
| ANO48329 |
When a GPRS session is released by dropping the DTR signal, sending ATO command to the Wireless CPU® does not return any response. In this case, a +CME ERROR: 3 should be returned because no GPRS session is active (DTR signal released the GPRS session) |
AT |
OTHER |
7.1b |
| CUS41945 |
If a CCID number containing digits between A and F is read with AT+CCID command, the digits are not displayed correctly. |
AT |
OTHER |
7.1b |
| CUS42132 |
When a SIM card is PUK locked and unblocked, and then this SIM is replaced by another one, the second SIM is rejected by the network. |
AT |
OTHER |
7.1b |
| CUS44786 |
No event is generated from the call service when a call is released by toggling the DTR. |
AT |
OTHER |
7.1b |
| ANO46201 |
For AT+CGACT=1 command, an OK is returned even if no PDP context exists. |
AT |
OTHER |
7.1b |
| ANO44106 |
The Wireless CPU® resets, if the Phonebook in the ME is full ( or almost ), and if the SIM is replaced by another SIM. |
AT |
PHONEBOOK |
7.1b |
| ANO41971 |
The phone book record size, retrieved by "AT+CPBR=?" can be wrong when a SIM with the EXT1 file is replaced by a SIM without EXT1. |
AT |
PHONEBOOK |
7.1b |
| CUS41593 |
After a phonebook entry in SIM card has been read by Wireless CPU®, the SIM card is removed and the phone number's length and TON/NPI are filled with 0XFF by using the SIM card reader.
Now, when the SIM card is re-inserted in the Wireless CPU® without resetting the Wireless CPU®, the phonebook entry in RAM is not updated. The RAM is updated when SIM card with different IMSI is inserted. |
AT |
PHONEBOOK |
7.1b |
| CUS41657 |
When a phone number length in a SIM phonebook is set to more than actual phone number length and the associate number is set to FF (after a first insertion of the SIM in the Wireless CPU®), the phonebook is not well displayed. |
AT |
PHONEBOOK |
7.1b |
| CUS42444 |
When the SIM PIN is blocked after 3 unsuccessful attempts to enter the PIN, the phonebook can still be accessed. |
AT |
PHONEBOOK |
7.1b |
| ANO41932 |
When ADN, FDN and LND phonebook are missing, the response to AT+CPBS=? is +CPBS: (,"MC","ME","RC","EN") and OK. It should be +CPBS: ("MC","ME","RC","EN") and OK (no comma before MC). |
AT |
PHONEBOOK |
7.1b |
| ANO44572 |
Wild card 'D' is saved incorrectly in the Phonebook by using +CBPW command. |
AT |
PHONEBOOK |
7.1b |
| CUS41943 |
When the phonebook character set is selected as CUSTOM or HEX and if the name field of the phonebook entry has a Ctrl^@ character (0x00) at the end, then this character is not displayed when reading the phonebook entry. |
AT |
PHONEBOOK |
7.1b |
CUS42508 and
CUS44230 |
When a SIM with a phone book record having a wrong value in the "Length of BCD numbers" field is used, the Wireless CPU® resets. |
AT |
PHONEBOOK |
7.1b |
ANO45922 and
ANO46331 |
Name associated to a FDN phonebook number will not be displayed when user reads an SMS coming from this number. |
AT |
PHONEBOOK |
7.1b |
| ANO42141 |
When SMS is written in CUSTOM and HEX mode(using AT+CMGW command), then the SMS is stored incorrectly. When AT+CMGR command is used to read this message, it is incorrectly displayed. |
AT |
SMS |
7.1b |
| ANO41982 |
SMS Replace type is not available for Flash SMS. If a SMS is received with the same PID and same OA as another already stored in flash, the 1st SMS is not overwritten by the 2nd one. The SMS Replace functionality is available for SIM SMS and should also be available for Flash SMS. |
AT |
SMS |
7.1b |
| CUS41972 |
The "+CIEV: 7,1" SMS storage full indication is received only when the 1st SMS storage memory (SIM or ME) is full. So the application is not informed when the 2nd SMS storage memory will be full. |
AT |
SMS |
7.1b |
| CUS44565 |
SMS reception is blocked if memory was full and a place has been released. (Memory available message not sent when SMS erased from full Memory). |
AT |
SMS |
7.1b |
| CUS40885 |
The last character of the Originating Address (OA) field in the SMS is lost when the OA field is in alphanumeric format. For example, if the OA field is "Voicemail", then on reading the SMS, the alphanumeric OA is displayed as "Voicemai". The last character is lost. |
AT |
SMS |
7.1b |
| CUS41974 |
In a SIM Tool Kit Session, when a GET INPUT proactive command is sent by the SIM to the Wireless CPU® with a Text String field present but with an empty text and a Default Text field, the Wireless CPU® makes a reset when the +STGI is returned. The Wireless CPU® should not reset and the +STGI with the right fields should be returned. |
AT |
STK |
7.1b |
| ANO44455 |
No STIN indication is sent to user if alpha ID is not present during a send SS and a send DTMF. |
AT |
STK |
7.1b |
| CUS41973 |
In a SIM Tool Kit Session, when a GET INPUT proactive command is received from the SIM by the Wireless CPU®, if the Text string field is empty and the Default text field is present, a coma is missing in +STGI command. The Wireless CPU® returns in this case:
+STGI:<InputFormat>,<EchoMode>,<SizeMin>,<SizeMax>,<HelpInfo>,<DefaultText> instead of
+STGI:<InputFormat>,<EchoMode>,<SizeMin>,<SizeMax>,<HelpInfo>,,<DefaultText> response. |
AT |
STK |
7.1b |
| ANO41897 |
Specific batteries might shut down because the charging duration of pulses is sometimes too long ( 1s in our static configuration) whereas some battery specifications say that maximum pulse should be lower. |
DEVICE |
ADC/BAT |
7.1b |
| CUS42197 |
If keys are pressed and released too quickly or simultaneously, keyboard can be blocked. And no new keyboard indication will be received until a Wireless CPU® reset. |
DEVICE |
KBD |
7.1b |
| CUS44201 |
Configuring DTE-DCE connection with 7E/O1 framing both on Wavecom Wireless CPU® and analog modem, establishing a CSD connection between the two of them, and sending data from Wireless CPU® to analog modem will fail. The parity bit is not transmitted and "Odd/Even" characters are not received on analog modem side. |
DEVICE |
V24 |
7.1b |
| ANO46693 |
When a data connection is established on a serial port (connected/online after a successful ATD replied with a CONNECT), if data is being received on radio downlink side, "+++" escape sequence on that port will fail to switch to offline/connected mode (AT command mode).
It is systematic for a CMUX port (even if no data is currently being received). |
DEVICE |
V24 |
7.1b |
| ANO41899 |
When A is sent for retrieving the previous command, an unexpected <CR> is echoed irrespective of echo mode and verbose mode. |
DEVICE |
V24 |
7.1b |
| CUS43788 |
When the UART speed is less than 9600bps, then it is not possible to make an outgoing data call (CSD) from the Wireless CPU®. |
DEVICE |
V24 |
7.1b |
| CUS43143 |
If the Wireless CPU® is switched on with automatic GPRS ATTACH disabled, if a PDP context activation is requested, the PDP activation procedure will take a long time if the network does not release the downlink TBF established to send the ATTACH_ACCEPT, and send the ACTIVATE_PDP_CONTEXT_ACCEPT on the same TBF. |
GPRS |
LLC |
7.1b |
CUS41986 and
CUS41886 |
If an incoming call is received and at the same time the user requests for a GPRS DETACH with "AT+CGATT=0", no response is received for the DETACH command. Also, "+CME ERROR: 515" is received when trying to answer the call. |
GPRS |
OTHER |
7.1b |
| ANO44466 |
GPRS transfer blocked ( reset needed ) under specific network configuration. |
GPRS |
RLC |
7.1b |
| ANO41891 |
When GPRS data transfer is active, sending of SMS over GPRS is not possible if the SAPI 7 priority is lower than the active SAPI user data priority. |
GPRS |
SMS |
7.1b |
| CUS41088 |
The "NO CARRIER" response is not sent to the application when a call, set on hold, is disconnected (by a network loss). |
GSM |
CC |
7.1b |
| CUS44775 |
If a call or SMS is done during a routing area update procedure, the Wireless CPU® may not leave the non DRX mode on paging channel. The impact is a loss of GSM service in some rare cases. |
GSM |
CELL_SEL |
7.1b |
| ANO47285 |
Layer 3 info service reports incorrect cell synchronization information when the GCC compiler is used. |
GSM |
CELL_SEL |
7.1b |
| CUS40690 |
If the EF Kc SIM file is corrupted, Wireless CPU® is not able to register to the network. |
GSM |
MM |
7.1b |
| ANO41889 |
No location updating procedure is performed in Network Mode of operation III when the class is changed from CG to B, and the Update Status is not updated, and the current LAI is the Lai stored in SIM. |
GSM |
MM |
7.1b |
| CUS41000 |
Reset occurs in some specific network in Italy when cell broadcasting channel is activated (Vodafone and TIM carriers) |
GSM |
OTHER |
7.1b |
| ANO46780 |
Wireless CPU® can reset during an FTP transfer if the RF signal is attenuated. |
GSM |
OTHER |
7.1b |
| ANO46894 |
In case of cell update in idle state, Wireless CPU® fails to select the best neighbor cell and can lose synchronization. |
GSM |
OTHER |
7.1b |
| ANO41888 |
If SIM files containing preferred PLMN lists are badly formatted, the Wireless CPU® resets just after entering PIN code. |
GSM |
PLMN_SEL |
7.1b |
| CUS42704 |
When the Wireless CPU® is registered for GSM service, if AT+COPS=2 is entered, followed by AT+COPS=0, receipt of calls/SMS becomes impossible. |
GSM |
RR |
7.1b |
| ANO41901 |
A Wireless CPU® reset occurs when frequency-hopping parameters are not valid in Packet Transfer establishment request. |
GSM |
RR |
7.1b |
| ANO40623 |
Even if the <OA> Originating Address or <DA> Destination address is present in the phonebook, the <alpha> field of the "+CMGR" response is always empty.
The <alpha> field should contain the correct details corresponding to the <OA> or <DA> present in the phonebook. |
GSM |
SMS |
7.1b |
ANO46278 and
ANO47515 |
When the Wireless CPU® performs an Interrogate SS operation, and receives a SS_RELEASE_COMPLETE with RETURN RESULT Component having a wrong content of Interrogate SS operation PARAMETERS, no error shall be generated because the PARAMETERS are optional. |
GSM |
SS |
7.1b |
| CUS42088 |
AT+CUSD=1,*770*078186480*100*00000# does not succeed because the Wireless CPU® sends a wrong SS version "SS-Protocol version 3" instead of "phase 2 service" in the message REGISTER. |
GSM |
SS |
7.1b |
| CUS42150 |
Low level "click" noise is audible at speaker when Wireless CPU® is switched to low consumption mode (32K) . |
HWL |
AUDIO |
7.1b |
| CUS44970 |
When waking up the target with an external interrupt, the wake up time is too long (35 ms). It should be reduced to a lesser value (up to 10 ms). |
HWL |
OTHER |
7.1b |
| CUS46304 |
After a voice call, the Wireless CPU® does not re enter sleep mode. It happens per 100 calls. |
HWL |
OTHER |
7.1b |
ANO48239and
ANO47317 |
In ADL, using adl_fcmUnsubscribe(...) API to unsubscribe to a subscribed UART flow (ADL_FCM_FLOW_V24_UART1, ADL_FCM_FLOW_V24_UART2, ADL_FCM_FLOW_V24_USB) makes the WIRELESS CPU® resets.
This is NOT the case for GSM and GPRS flows. |
OTHER |
OTHER |
7.1b |
| ANO41842 |
When the Wireless CPU® has been started by an RTC alarm, ADL does not inform the application with the start cause (the initialization type is detected as a normal one). |
OTHER |
OTHER |
7.1b |
| ANO45374 |
The ATR is not valid with one specific Schlumberger SIM card when SIM speed enhancement is On. |
SIM |
OTHER |
7.1b |
| ANO47481 |
Using FCM APIs, unsubscribing to a subscribed flow makes the Wireless CPU® reset. This is the case for OSA sample also. |
SIM |
OTHER |
7.1b |
| CUS48081 |
The SIM cannot be detected when the SIMREMOVE feature is disabled and if the SIMPRES is low. |
SIM |
OTHER |
7.1b |
| ANO47140 |
When the SIM REMOVE feature is de-activated, the PTS_EXT_INT_8 which is multiplexed with the SIM_PRES signal is not available for the user.
However, GPIO18 (which is multiplexed with PTS_EXT_INT_8 too) is available for the user. The PTS_EXT_INT_8 should be available once the SIM REMOVE feature is de-activated. |
SIM |
PRES |
7.1b |
| ANO48097 |
"+WIND: 0" indication is not displayed after resetting the Wireless CPU® when SIMREMOVE feature is de-activated/disabled. |
SIM |
PRES |
7.1b |
| ANO46451 |
AT&T test SIM 4A (Schlumberger 32k Non-GAIT Retail SIM) is not detected. On issuing AT+CIMI command, the Wireless CPU® returns CME ERROR: 10. |
SIM |
RESET |
7.1b |
ANO44691 and
ANO48193 |
Wireless CPU® resets when SIM is removed and inserted into the SIM rack (stress test). |
SIM |
RESET |
7.1b |
| CUS41993 |
While waiting for the user input for SIM toolkit functionalities, the Timeout, set by the "AT+STSF" command, expires before the expected time when the Timeout duration is greater than 2 minutes. |
SIM |
STK |
7.1b |
| ANO47288 |
Wireless CPU® does not switch to slow idle mode when FCM is switched to data mode and then DTR is toggled to low. |
OTHER |
OTHER |
7.1b |
| ANO47439 |
It is not possible to execute an Open AT® application signed (SDS) with IDE 1.06. AT+WOPEN=7 status remains 15 forever and adl_main () is never called. |
OTHER |
OTHER |
7.1b |
| ANO48938 |
[IDS] Impossible to install a DOTA/RDMS update if UART1 port is opened and if the UART1 cable is unplugged |
IDS |
N/A |
7.1b |
| ANO49148 |
[IDS] When the GPRS session is closed (by the user or by the network), the connection to the IDS server is not possible after around one hour of inactivity |
IDS |
N/A |
7.1b |
| CUS49272 |
New flash driver for management of flash ST 65nm |
FMS |
OTHER |
7.1b |
| ANO49289 |
The delay between the deactivation of the SIM and the new class selection is less than 10 ms (recommended by the specification 7816-3). |
SIM |
OTHER |
7.1b |
| ANO49460 |
SIM interface is not turn off when the ME is using an unsupported class SIM. FTA tests are failed : 27.17.1.5.2 (3V only), 27.17.1.5.6 (1V8 only) |
SIM |
OTHER |
7.1b |
