Firmware 7.52.0.A1 Release Notes
- Oct 14, 2015
- Author: Sierra Wireless
- Version: 7.52.0.A1
Contents
2. Abbreviations and Definitions
5. Software Release Description
6. Software Changes Description
9. Restrictions and Additional Information
List of Figures No table of figures entries found. List of Tables
Table 2. Abbreviations and Definitions
Table 3. Related Documentation
Table 4. Hardware Compatibility
Table 5. Software Compatibility
Table 6. Open AT Firmware Release Information
- Introduction
- Document Scope
- Document Audience
- New Features/Enhancements
The scope of this document is the Firmware 7.52.A1 release description for the AirPrime listed in the compatibility section.
This release note may be distributed to all direct and indirect customers and will be posted in Sierra Wireless Developer Zone
|
Feature |
Description |
|
Audio support |
Following list of AT Commands and unsollicited event have been added: +SPEAKER, +CMUT, +ECHO, +WVR, +VTD, +VTS, +WDDM, +VIP |
|
CMUX protocol is able to run over UART. +CMUX AT command has been added. |
|
|
TX Burst indication |
TX Burst Indication is available through +WTBI command. |
|
Abbreviation/Acronym |
Definitions |
|
ACCM |
Async-Control-Character-Map |
|
AT |
Attention |
|
DCE |
Data Circuit Equipment |
|
DTE |
Data Terminal Equipment |
|
DTMF |
Dual-tone multi-frequency signaling |
|
DTR |
Data Terminal Ready |
|
GPIO |
Global Purpose Input Output |
|
GPRS |
Global Packet Radio Service |
|
IMEI |
International Mobile Equipment Identity |
|
LCP |
Link Control Protocol |
|
ME |
Mobile Equipment |
|
MS |
Mobile Station |
|
PDP |
Packet Data Protocol |
|
PLMN |
Public Land Mobile Networks |
|
PPP |
Point-to-Point Protocol |
|
SIM |
Subscriber Information Module |
|
STK |
SIM Application Toolkit |
|
TCP |
Transmission Control Protocol |
|
UART |
Universal Asynchronous Receiver Transmitter |
|
UDP |
User Datagram Protocol |
|
BOOT |
Boot loader |
|
AMMS |
AMSS firmware |
|
HYPER |
Virtualization layer |
|
OAT_NVP |
Open-AT firmware NV parameters |
|
Open-AT firmware |
|
Ref. # |
Doc. # |
Document title |
|
[1] |
4111843 |
AT Commands Interface Guide for Firmware 7.52 |
|
4111844 |
ADL User Guide for Open AT Application Framework OS 6.52 |
|
|
[3] |
4114417 |
Firmware 7.52 Customer Release Note |
|
[4] |
4111754 |
AirPrime - Q2698 - Product Technical Specification and Customer Design Guidelines |
|
Component |
Version |
|
Firmware |
7.52.0.A1.201401021703.Q2698 |
|
Open AT OS |
6.52.0.A1.201306271522 |
|
Location Library |
1.4.6.201305151408 |
|
eCall inband Modem Library |
Not supported |
|
Security Library |
2.2.0.201306261000 |
|
Internet Library |
5.56.0.A1.201307011505 |
|
Extended AT Application |
1.3.0.A1.201307021020 |
|
Component |
Revision |
|
Boot loader |
SWI6200T_02.02.04.07ABT R2881 CNSZXD00000132 2013/12/20 10:43:54 |
|
Application |
R7.52.0.A1.201401021703 |
|
Date of generation |
2014/01/02/17/03 |
|
Binary Size |
1770396 bytes |
|
Checksum |
0xae3e7f98 |
|
IMEI SV |
3 |
|
Qualcomm Stack Version |
SWI6200T_02.02.04.07AAP R2881 CNSZXD00000132 2013/12/20 10:57:19 |
|
USB Host Version |
|
|
Firmware(ATI9) |
"DWL"," SWI6200T_02.02.04.07ABT R2881 CNSZXD00000132 2013/12/20 10:43:54","","Sierra Wireless",0,"","00000000","00000000" "FW","FW_752_28_A1_12.Q268Fx","R7.52.0.A1.201401021703.Q2698","Sierra Wireless",1770396,"010214 17:03","ae3e7f98","10002020" "MODEM 3G+","Revision: SWI6200T_02.02.04.07AAP R2881 CNSZXD00000132 2013/12/20 10:57:19" … "ROM","8400000" "RAM","4000000" "OATRAM","40000" "DWLNAME","Q2698" OK |
- Software Tools Versions
|
S/W Tools Name |
Version |
|
Developer Studio |
2.3.1 and upper |
This section presents the download procedure for the customer.
|
Download Option |
Files |
|
|
Upgrade through Xmodem |
Bootloader |
SIERRA_BOOT_SWI6200T_02.02.04.07A.dwl |
|
Firmware |
For Q2698 : SIERRA_OAT_FW_R752A1_FULL_q2698.dwl For FX100: SIERRA_OAT_FW_R752A1_FULL_fx100.dwl |
|
For the upgrade procedure, you can refer to:
- Troubleshooting
- Certification Description
- Restrictions and Additional Information
|
Comment |
|
|
None |
None |
For Open AT Developers, please refer to the Troubleshooting Guide available in Developer Zone before contacting customer support.
For AT developers, please contact customer service for support and debugging information.
|
Product |
GCF-CC |
NAPRD.03 |
AMSS SWI6200T_02.02.04.07A |
3.51.1 |
5.17 |
|
Description (What/When) |
Impacted Domain |
Impacted Sub-Domain |
|
|
71304 |
Audio gains AT commands are not available (AT+CLVL, AT+WDGR, AT+WDGT, AT+VGR, AT+VGT & AT+SIDET ) |
AT |
AUDIO |
|
67458 |
+WADS must not be used as it could freeze the module |
AT |
AUDIO |
|
67014 |
+WDTMF is not functional |
AT |
AUDIO |
|
67261 |
Cannot hear from module and from the other side if restore audio default setting (AT&F) during call |
AT |
AUDIO |
|
68553 |
+CTZU not working |
AT |
OTHER |
|
70198 |
+WUSS and +CMMS command are not available as soon as the +WIND: 3 indicator is received |
AT |
OTHER |
|
70442 |
Module returns wrong signal value (with +CIND) when antenna is removed from module |
AT |
OTHER |
|
70444 |
No "+CIEV: 2,X" message is received after antenna is removed from module |
AT |
OTHER |
|
70449 |
No error indication is received when a forbidden operator is selected with +COPS |
AT |
OTHER |
|
70527 |
+WIND:7 is not received until CPIN is not entered |
AT |
OTHER |
|
71084 |
Cannot enable call barring service |
AT |
OTHER |
|
71085 |
AT+CHLD=1 should only disconnect the active call, but all calls are currently disconnected. |
AT |
OTHER |
|
66047 |
Cannot activate some +WLCK command facilities |
AT |
OTHER |
|
66143 |
When call forward is disabled, +CCFC is not allowed to show the number. |
AT |
OTHER |
|
68744 |
<LAC> and <CellId> field value are not reported correctly through CCED response. |
AT |
OTHER |
|
68794 |
FDN enable with +CLCK is not persistent after AT+CFUN=1 |
AT |
PHONEBOOK |
|
70300 |
Phonebook is not stable for writing and finding |
AT |
PHONEBOOK |
|
70219 |
Deleted LDN phonebook entries still appear after AirPrime restarts on deleting the LDN phonebook by AT+WDCP="LD" command. |
AT |
PHONEBOOK |
|
67384 |
Sometimes + CMS ERROR: 500 could result after sending specific SMS |
AT |
SMS |
|
68944 |
Q2698 could not receive sent SMS when module is switched on |
AT |
SMS |
|
69108 |
Module cannot receive SMS with extended character |
AT |
SMS |
|
70345 |
Wrong SMS read on PDU mode, class 2 (CMGR/CMGL) |
AT |
SMS |
|
70760 |
Reset when sending large SMS ( size superior of 140 characters) |
AT |
SMS |
|
70455 |
[STSF]No +STIN indication is returned when auto response is activated |
AT |
STK |
|
67263 |
[ATDL]Cannot redial the last number if restore factory setting with AT&F |
AT |
OTHER |
|
70482 |
Wrong USSD status is received after unlock the PIN code when result code presentation is enabled |
AT |
OTHER |
|
68762 |
No audio heard on incoming voice call when using Telstra 3G network (in a AMR-WB supported cell) |
CALL |
AUDIO |
|
69450 |
A twisted busy tone is heard in earphone (after one second) |
CALL |
AUDIO |
|
71060 |
PCM audio profile setting of speaker 9 is not correct |
CALL |
AUDIO |
|
70574 |
Audio file is not played after an ongoing call is hung up |
CALL |
AUDIO |
|
69133 |
Not receiving DNS address in Telecom XT network in New Zealand |
DATA |
OTHER |
|
67808 |
[ADC] Long delay of changes in AT+ADC? and AT+ADC=0,0 return values following changes in ADC0 value |
DEVICE |
ADC |
|
66299 |
[OAT/BUS]Data read from SPI bus chip does not match the data written into it |
DEVICE |
BUS |
|
67678 |
Errors could happened when using adl SPI bus functions with Ethernet application |
DEVICE |
BUS |
|
68254 |
adl_busRead () API for SPI bus could lead to Wireless CPU freeze |
DEVICE |
BUS |
|
68383 |
No response from SPI bus after a stress data write/read test in asynchronous and synchronous mode |
DEVICE |
BUS |
|
69259 |
Sometimes I2C controller detects fake failure and that causes error -2 with adl_busRead() & adl_busWrite(). |
DEVICE |
BUS |
|
69647 |
Couldn't subscribe to SPI bus with Clk_Speed setting in 17-24 range |
DEVICE |
BUS |
|
69651 |
[FX100) After Open AT application is stopped and started, IESM Ethernet driver subscription may fail. |
DEVICE |
BUS |
|
69832 |
Bad throughput performance on Ethernet device |
DEVICE |
BUS |
|
70256 |
[OAT] SPI address and data bits are separated by many cycles |
DEVICE |
BUS |
|
71022 |
I2c exchanges are slow. About 300-400µs per byte whatever the I2c clock (standard or fast). |
DEVICE |
BUS |
|
67623 |
Sometimes chip select output of SPI does not toggle during sequential execution of read and write operation. |
DEVICE |
BUS |
|
70636 |
Wrong response of sending DISC string with + CMUX |
DEVICE |
CMUX |
|
69861 |
When FCM flow is opened on an UART, Data blocks with size having multiple of 56 bytes is not notified by FCM. |
DEVICE |
FCM |
|
66771 |
Got Error:502 by stress test of WIOR command |
DEVICE |
IOB |
|
66785 |
Module freezes when allocating some GPIO pin as Output with Logic Low level |
DEVICE |
IOB |
|
69627 |
GPIO0 subscribed as OUTPUT by using application switches its direction to INPUT after calling adl_extintSubscribe API |
DEVICE |
IOB |
|
67251 |
Wrong GpioDir and GpioVal returned by AT+WIOM? |
DEVICE |
IOB |
|
71095 |
Sleep mode does not work when AT+W32K is issued through a CMUX channel |
DEVICE |
MUX |
|
68512 |
[FX100] Reset occurs using open uart and no device on uart 1 connected. |
DEVICE |
OTHER |
|
69747 |
When DTMF service is used with application, DTMF detection is failed. |
DEVICE |
OTHER |
|
70554 |
Junk SecondFracPart is retrieved when calling adl_rtcGetTime () API. |
DEVICE |
RTC |
|
69606 |
[FX100] Ethernet gateway sample starts with error (irq subscribe failed: -5 ) |
DEVICE |
SYS |
|
66213 |
When UART DTR pin is constantly on, FX100 does not respond to AT commands after AT+WDWL & AT+WOPEN=1. |
DEVICE |
UART |
|
67098 |
The Dev Kit detects only USB high Speed port and not USB full Speed port |
DEVICE |
USB |
|
67084 |
Module does not reply to AT command when setting ICF_7M1 (AT+ICF=5,2) |
DEVICE |
V24 |
|
69860 |
adl_portGetSignalState() return wrong value of RTS signal |
DEVICE |
V24 |
|
66197 |
adl_adinstall() function issue after the installation of application |
FLASH |
DOTA |
|
70093 |
adl_fsInstall() cannot install open AT with hardware reset during the installation progress |
FLASH |
FILESYSTEM |
|
68768 |
adl_fsInstall() API may return an error code instead of installing the dwl file if a bad block is present in the FOTA partition |
FLASH |
FILESYSTEM |
|
69228 |
NO CARRIER could be not received after the disconnection of a connected dial up |
GPRS |
OTHER |
|
70311 |
When command AT+CGACT=0 is issued for second GPRS deactivation then no response is received and no command can be issued further |
GPRS |
OTHER |
|
69599 |
[FX100] cannot send SMS after AT+CGACT=1,1 |
GPRS |
SMS |
|
69776 |
SMS not being sent in GPRS mode |
GPRS |
SMS |
|
70995 |
[WIPSoft]Incorrect response_time values returned for the AT+WIPPING command |
OAT |
OTHER |
|
67417 |
The user is not able to start the DHCP server on the module. |
OAT |
OTHER |
|
66012 |
[GpsOne] Cold start TTFF results over expectation |
OAT |
OTHER |
|
66205 |
[GpsOne] GPS library is not compatible with Embedded module sleep mode |
OAT |
OTHER |
|
69585 |
SIM pin remaining attempts not correct when using adl_simRemAttempt() |
OAT |
SIM |
|
67876 |
Return value of adl_tmrUnSubscribe is not correct |
OAT |
TIMER |
|
68434 |
adl_osclkGetTime does not return 4.615 based values |
OAT |
TIMER |
|
66338 |
Higher power consumption than expected in Low power consumption mode (WBHV=1,x) |
OTHER |
OTHER |
|
66342 |
Startup time is too long |
OTHER |
OTHER |
|
70481 |
After few normal restarts (due to +WOPEN, +CFUN), AT+WDWL doesn't launch the xmodem bootloader |
OTHER |
OTHER |
Tags
Related items
AT Commands Interface Guide for Firmware 7.52This document provides full description of AT commands supported by AirPrime wireless modules and AirLink Programmable Gateways.

Open AT Application Framework 2.52.0.A1 for Q2698_FX100Open AT® Application Framework 2.52.A1 package contains: